Featured Post

Subscribe!

Monday, April 11, 2016

Triumph Spitfire Anti-Sway Bar Disassembly

This is my 100th post. Nothing special, just thought I'd mention it. Maybe I should talk about something momentous, but nah.

Anyway, while playing with the steering rack I also decided to clean up the anti-sway bar from the '64. I pulled the old mounting rubber off and took a flap disk to it to clean up all the gunk.

All cleaned up. Hey where'd that beer come from?! I hope it was after 5pm! Good reason to not have a time stamp on my pics.
The removal of the links was a little tricky but they didn't fight me as much as I thought hey would. Both of them turned right out of the end of the bar, but I had to put the link in a vice to get the bolts of of the link itself.

Link removed. The ball end bolts the lower A-arm while the other screws into the anti-sway bar.

Where the link attaches.

Using the vice to help break away the stud in the link bushing. Not as bad as other bushing problems I've had, that's for sure!
Otherwise, there wasn't much else to it. There was one interesting find in that I think the thing is quite bent. So bent, as a matter of fact, that it may be no longer effective. I decided to pull the one of the '66 to see how that was. Turns out this one was bent, too, though not as bad.

It should be resting flat on the bench (and, yes, the bench is pretty level). The end rises about an inch from where it lays flat.
Of course, I didn't pay attention when I pulled it off the '64 but it seems as though the driver's side on the '66 was the bent part; probably the same on the '64, I figure. This stuff is spring steel so I think I can forget about being able to straighten it out, at least using the tools that I have here.

Interesting, though, that they are both bent in the same way, though not to the same extent. I posted about it on my favorite forum. It got quite a bit of play with discussion ranging from "it's just bent" to "they did that on purpose to account for the weight of the driver". Of course, this would assume that Triumph designed the car around the assumption that only one person would be in it AND that you would have different parts for both the left-hand drive and right-hand drive cars. The part numbers are the same.

Though I've come to believe that the bend is not intentional (otherwise I would expect the same "bent-ness" from both bars made only 2 years apart), I find it odd that all of the forces acting on the car during the need for anti-sway are focused right to that point and cause some 3/4" to 1" tempered steel to bend and NOT cause other deformations elsewhere in the car...or at least none that I could find. Like I said, interesting.

That's it. Here's to 100 posts. Maybe by about post 1283, the car will be done!


Sunday, April 10, 2016

Triumph Spitfire Steering Rack Final Assembly

Finally finished up the steering rack assembly today. I never did get the measurements figured out completely, but I'll get into that. Essentially all I had to do was get the rubber boot on that I had ripped and then get the measurements for initial fit as close as I could. Of course, I totally tore it apart to get this done. Glutton, I know.

If you remember from my last post on this subject, I was confused about some measurements that workshop manual called out. Because I really didn't understand how the measurements were working, I pulled the whole thing back apart to measure on the rack itself. In support of this and for measuring some "before" body points to make sure I keep her as square as possible when I tear into those repairs, I bought myself a Singer Pro Series Retractable Pocket Tape Measure 96". This is like my Harbor Freight Professional Series angle grinder...because, you know, I'm a professional. Oh, and it's pink.

Measuring between the inner faces of the lock nuts.
First thing I did was screw both inner ties rods in until they bottomed out. The distance between the inner faces of the sleeve nuts was about 635 mm (metric was easier for figuring this stuff out instead of fractions of an inch). I then measured the width of the locknuts at about 7 mm. If my math is correct, that puts the inner faces of the locknuts at about 621 mm if they are just touching the sleeve nuts. Now, here's what the manual says:

"1. Screw the locknut (33) on to the end of  the rack (32) so that its position corresponds with dimensions  3  +  4  +  5  +  3  on  Fig.  1, i.e.,  24.40"  (619.76  mm.)  between  inner locknut  faces. 
2.  Insert  the  spring  (36)  into  the  end  of  the rack  and  screw  the  ball  joint  assembly as far as possible up to the locknut  (33)."

I read this to mean that the ball joint assembly should reach the locknut before it bottoms out. My favorite forum was in agreement. Obviously, doing the math, that just isn't enough extra mm's to let this work. So, I set the spacing between the inner locknut faces at about 625 mm and went from there.

I put it all back together, including the new tie rod ends while observing their measurement settings and without all of the confusion.

Tie rod end attached. I used teflon tape, like for water pipes, to mark the approximate measurement position, though this turned out to be unnecessary.
I took another shot at the new rubber boots. There are two, obviously. Both have a small opening at one end that gets clamped to the inner tie rod and the other two ends are of different sizes. The larger of the two ends clamps to the rack housing while the other clamps to the rack tube. The larger one was pretty easy, but the small one is tough to get over the inner tie rod nuts. Using a recommendation from the forum, I used the upper end of a water bottle, cut off about 3 inches down from the opening. I then cut this so I could overlap the plastic. I put the bottle on, bottom first, so that the opening went up to the nuts and the remaining plastic covered them. This provided for a relatively smooth transition up and over the nuts to hopefully allow me to stretch the rubber over them.

I then put the boot on, positioned the rack assembly on the workbench so I could push on it, and pushed and pulled the boot up the plastic and over the nuts. Damn if it didn't work!

Not the best picture, but you can see the opening flaring up over the plastic bottle which is covering the nuts.
Unfortunately, however, the boot "ate" the bottle. Couldn't leave that inside there, so, I left the end over the nuts to let it stretch out for a while. I then quickly pulled it off, got the bottle out of there, and jammed the boot back over the nuts. Thankfully the rubber stayed stretched enough to allow this (it was chilly in the garage and the rubber was a bit stiff...probably helped).

Rubber boot end covering the nuts. I left it this way to let it stretch out a bit.
After I high-fived myself for getting that done, I clamped the boot ends down, made sure they would take full motion of the rack and gazed upon my success! Now if only the rest of the car looked this good! At least the steering rack will be waiting when she's ready.

Looks just like the last picture in my previous post, but this thing is actually done this time (the u-bolts were attached after this picture, so I guess not done-done).
I have another post coming soon about the anti-sway bars that I pulled off both cars and the fact that they are bent...I think. Also the cool curly-cue u-bolts that attached it on Dorothy.

Curly-cue attachment u-bolts from the '66 (Dorothy). The '64, and the workshop manual, just show standard u-bolts.

Sunday, April 3, 2016

Building Vehicle Dollies

No direct car work today but work in support of it.

One of my more favorite movies is Jurassic Park. There is a quote, for the character of Dr. Ian Malcolm, that goes "Yeah, yeah, but your scientists were so preoccupied with whether or not they could that they didn't stop to think if they should."

As you all know, I buy quite a bit of stuff at Harbor Freight. While I wouldn't say that I'm on a very strict and limited budget, I'd much rather spend my money on good parts than on good tools that I will end up using very rarely. And, while I've only been burned by one of my larger purchases there, I also wouldn't buy something like a Harbor Freight MIG welder, either. I cannot stress enough to keep your receipts! They allow returns within 90 days BUT ONLY WITH A RECEIPT. I bought a vise for about $50 and over-tightened the swivel clamp and stripped it right out. I had trashed my receipt and shortly after, trashed the vise. The reviews on their vises aren't that great. In hindsight, it was a mistake to buy one there. But, enough of that...

One of the things I've had my eye on for a while is their Vehicle Dollies. While I rarely buy anything big there without one of their coupons, at about $40 a pair, I think they are pricey for what they are. If I had a big shop that I needed to move the car around it, it would be a no-brainer. But, I just want to be able to move the car a few feet in any direction to give me some more room when I'm working in a particular area. So, $80 was just a bit too much. I tossed around the idea of making my own, but just the swivel casters were about $4 each. At $64 just for the wheels, again, a bit too much. But, then I had an idea...

There was a coupon for their Mover's Dollies for about $8 each. They were rated for about the same capacity (1000 lbs). Of course, they were made of wood and had a big hole in the middle, but maybe I could do something about that. So, for $32 +tax, I picked up four of them.

First thing I did was take them apart. While I tore the carpet off that is attached to them, it is only held on with staples. I pried the staples off with a flat-head screwdriver and, if I was careful, I could have done that all the way around and save the carpet for re-installation. I just didn't see the point. Also, MOST of the bolts were already loose. While not only finger-tight, they were definitely not as tight as I would want them so if you are using these things in general, I would check on this before using them again.

Dolly from the bottom - as bought.
Next were the casters. Of course, I came across two different attachment methods and had unknowingly bought two of each. One way used carriage-like bolts, flat washers and lock washers. The other method used Phillips-head machine screws and nyloc nuts with no washers. Given the choice, I would prefer to use the Phillips-head method because it just seemed easier to make it work. I did note an external difference between the two styles, so you can pick the right one if you choose. In the long run, however, both were not too difficult and I would buy either kind to modify.

The burned-in label on the preferred design dolly.
Fortunately, the four pieces of wood are glued together so when you pull the caster bolts out the whole thing stays together. I had initially left a few screws in (you'll see that in the picture below) to keep everything aligned before I figured out it was all glued.

While I think the open bottom of the dolly would have been okay, I wanted to give something for the bottom of the tire to rest on to distribute more of the weight of the car. Also, this is how the "real" dollies are designed so I figured it would be a good idea. I bought a $5 piece of 1/2-inch plywood that was 2 x 4 feet. Each dolly measured about 17 3/4" x 11 1/2" and I cut a piece of plywood to about these dimensions. I centered the plywood up on the dolly and clamped it using a bar clamp (also Harbor Freight).

Clamped. The 12" bar clamps have pretty bad reviews, but they've worked "Harbor Freight good enough" for me.
Once clamped and steady, I used a drill bit just slightly larger than the screw and, using the existing holes as a guide, drilled through the plywood. I had originally intended to buy longer screws to make up for the extra thickness of the new plywood, but they run about $0.30 each. While this may not seem like a lot, when you add it up, that's almost $20 just in screws which would bring this whole thing close to defeating the purpose. With some more modification (below), I used the same screws.

I decided to put the plywood on the bottom of the whole thing to provide a bit of a recess that the tire could sit in while also providing a lip all around to minimize the chance of rolling the tire off of the dolly. To be able to use the same length screws, I used a 1/2" drill bit to cut a relief in the top of the dolly to provide a large countersink for the screw heads. I decided that about half-through the thickness of the board was probably good enough and I marked the drill bit to give me an idea of how deep I wanted to go.

Drill bit marked with Sharpie for a depth gauge.
Once that was done, I essentially slapped it all back together and tightened down the screws. I also greased the caster bearings (some were greased and others weren't).

Completed dolly, bottom side (obviously).

Completed dolly, top side. You can see the screw reliefs that I drilled.
Car on the dollies. They work, so there's that.
I dare say that I would recommend going this route if you don't mind taking a few hours. For about $40, I was able to build/modify four vehicle dollies that would normally cost me almost $80 (or $100+ without a coupon). They are definitely not as slick looking as the metal ones, but my guess is they are strong enough for a little car like this and will work just as well.

Back to the movie quote; while I was on the fence about getting the actual metal vehicle dollies, once I got it in my head of trying to do this, I just did it without really thinking if I should. It took an afternoon to accomplish and I'm not sure that I will really need to move the car around all that much. I also discovered that my 1.5 ton Harbor Freight jack does not have enough height to raise the car high enough to get the dollies under the wheels. I used my larger 3-ton Sears jack, but I'm sure a block of wood on the HF one would have done the trick.

So, while I'm glad I did it, I think if I had dropped the $80 on the metal ones, I would have taken them back. Who knows, though. Maybe that will become invaluable in mysterious ways. If I had a bigger garage that I could actually move stuff around in...these would be almost a necessity, I think.

Monday, March 21, 2016

Triumph Spitfire Steering Rack Cleaning and Assembly

I've been slowly putting the steering rack back together over the last few days. A snow day for the kids and I (wife was out of town) today. As usual, the local school districts do a knee jerk and call school off rather than delaying it 2 hours. Most of the snow was melted by the end of that time. Back in my day! Anyway, this is a rather lengthy post so fair warning.

NOTE: If you decide to do this, I cannot stress enough to keep your parts separated by group (e.g., driver's side inner tie rod), bagged and labeled. There are items that are easily lost and several stacks of shims that make up required measurements, all of which I'm sure are not easily replaced.

Previously, I had gotten as much of the old grease and grime and rust and everything else that wasn't supposed to be there cleaned out. I soaked some of the rusty bits in vinegar overnight and wire brushed them. I took a wire wheel to everything (both using a drill and a Dremel Rotary Tool) and also some 220-grit sandpaper to some of the bearings, collars and washers to remove the surface corrosion that made taking the thing apart a bit of a chore. I also pushed a clean rag through the rack tube a few times using a wooden dowel that cleaned everything right up. A coat of Rustoleum Gloss Black was applied to the stuff that would take a painting.

Inner tie rod ends with threaded and ball ends taped over.

Steering rack tube cleaned and painted. The pinion housing is aluminium so it's not painted.
There is a brass bushing in the end of the steering rack tube, opposite the pinion housing. It's a combination of designs of the brass thrust washers and gear bushings I found in the transmission and I thought it was interesting to find it here.

Bushing. SpitBits does sell them, but I'd hate to have to get one out and a new one in!
You can clearly see the dimples and just barely see the dark groove towards the bottom center-left. This groove is spiral cut and runs the entire circumference of the bushing from bottom to top in this orientation. These types of bushings existed before technology came up with sintered, or oil-impregnated, bushings. The dimples hold the oil/grease when things are static so it is ready to provide lubrication when things start moving. The spiral promotes movement of the oil/grease up and down the bushing as, in this case, the steering rack moves along it. A thank-you to my brother for educating me.

Assembly was also a good excuse to take a trip to Harbor Freight to get some more stuff which I'll talk about as I go. As with my previous post, I'm including some exploded views of the whole process from the workshop manual and including these part numbers in parentheses after the part name, as applicable. Everything I'm doing follows the Workshop Manual unless stated otherwise. However, there are several measurement points with various specifications that I do not go into. Please, if you decide to tackle this, ensure you have a good reference. Besides brakes, this is probably the next most important safety-related item you've got.
Now, on to the show.

First portion of assembly was getting the pinion assembly end float measured and set. This required putting it together inside the pinion housing without any shims (12). 



Pinion Assembly after cleanup. I couldn't get the bottom bush (17) out of the pinion housing, so I left it.
The rubber o-ring in the upper left of my photo is not identified in the manual figure. It fits inside the recess in the retaining ring (11). I was able to source a pair of these from my local True Value for about $1.50. I couldn't see a difference by comparison by eye between the new and old.

These were identical as far as I could tell.
To measure the end float, I purchased a Clamping Dial Indicator from Harbor Freight. Not the highest quality of stuff, but I bet it's as good as they had in the 60's. It did the trick.

New Toy #1
Dial indicator set up. Not zero'ed out in this picture.
The end float came out to be about 0.040" which, funny enough, was just about the exact thickness of the shims (12) that I pulled out. How do I know this? Well, I measured the shims with my other new toy, the Harbor Freight 6 in. Digital Caliper with SAE and Metric Fractional Readings. I had a coupon for this so it was like $11. A bit flimsy, but it works.

Thickness of the three pinion assembly shims. And, new toy #2.
Once complete, this was all loaded back in the pinion housing, including shims this time, new o-ring and the dowel peg (5) which the manual tells you to be careful not to lose. Yeah, thanks....almost did about 9 times.

The dowel peg (5). 
Next was assembly of the pinion pressure pad. This also required some measurements and shims (29) and, as expected, it all went back together just as it came apart with good measurements.


0.026" gap. Again, funny, almost perfectly accounted for by the shims.
After this is all assembled, there is a test for measuring resistance that entailed suspending a 2-pound weight 7.9" from the pinion. I couldn't come up with a slick way to do this, so I didn't. Hopefully this will not impact me in the future.

Next was putting the tie-rod inner ball joints (38) on. I followed the manual for measurements and assembly instructions and used the shims that were already there. I used new lock tabs (35) to make it all good.


Locking down the lock tab (35). Squeezed in a vise vice using a hammer.
The lock nuts (33) are then put on either end of the steering rack and are spaced 24.4" from the inner side of each nut. This was a tricky measurement because you are dealing with a relatively long distance over an uneven surface. I eventually got it right. The manual doesn't really mention whether you should expect to bottom out the inner tie-rods into the steering rack, but only says to screw them in until they meet the lock nuts. Once I got the measurement correct, the tie-rod ends met the lock nuts before they bottomed out, so I assume this is the correct way to do it. Definitely something that you have to experience trying yourself to understand clearly. Once this was assembled, I tightened the lock nuts (33) into the inner tie-rods(38).

Once done there, the next step was to put on the big rubber bellows or boots. Of course, I tore one as they are not that easy to deal with. I can't imagine how much money my impatience has cost me when I know better. Anyway, I kept going to try and learn more lessons but I have a set on the way from SpitBits.

Whooops.
The manual tells you to grease and put the boots on and secure them with the clips. You can grease them, but I wouldn't secure them yet. There are additional measurements you need to take to get the outer tie-rods sets right and the boot gets in the way since it covers the inner tie-rod lock nut, which is what one of the measurements is based on.

I ordered new outer tie-rods from The Roadster Factory as part of their front suspension major rebuild kit a while ago. While they are nice, the threads were very dirty on the inside with machining residue. I figured this out when I tried to thread it up the inner tie-rod and it starting galling. Fortunately, I didn't strip any threads and used a brass round brush and some de-greaser to flush it out and clean it up.

Thread-cleaning kit.
Another measurement to take is the center of the outer tie rod (where the grease fitting is) to the inner portion of the inner tie-rod lock nut. This should be 10.13". This was a painful because of the rubber boot being in the way and what-not. On the second side, which I hadn't put the boot on yet, I screwed in the outer tie rod and got it measured up properly, then marked the threads with red Sharpie. Luckily, assembly of the boot, the lock not and tie rod did not remove the Sharpie totally and I was able to get very close to that 10.13".

Red Sharpie mark. The outer tie rod lock nut came off before the boot when on so I didn't tear another one.
That was about it. I'm sure there will be several and probably frustrating measurements and adjustments to make once I get this on the car. But, at the rate I'm going, that will be so far in the future that I won't remember any of this anyway! Of course, I have to take one side back apart to get the new boot on, so there's always that.

In all her glory.
Oh, and one other Harbor Freight toy was an extension cord on a reel so I don't have to drag cords across the garage. There aren't a whole lot of outlets in there and this will help with my garage re-arrangement. I also got a halogen light to go along with it because the new corner that I'm working in can get kinda shadow-y. Oh, and a welding table, (on sale) but that's for another post!


Thursday, March 10, 2016

Triumph Spitfire Steering Rack Disassembly

For my regular readers (both of them), you know that I have a logistical problem that I have complained about for a while. Specifically, my lack of garage space. In a probably futile effort to more efficiently use the space that I do have, I was able to move some more parts up in the attic and open up some shelf and floor space. This enabled me to put "real" legs on my previously sawhorse mounted workbench (this guy) and move it against the garage wall instead of in the middle of the floor behind the car.

New work bench location. Yes, I have three snow shovels. Last year was bad, okay?
Doing this gave me about 4 feet behind the car so I pushed her back a bit and now have good room in front and behind. The sides are still an issue, but I'm pretty much screwed there. Little steps, I guess.

Behind the car. At least I can get around it better than when the workbench was there.
NOTE: If you decide to do this, I cannot stress enough to keep your parts segregated by group (e.g., driver's side inner tie rod), bagged and labeled. There are items that are easily lost and several stacks of shims that make up required measurements, all of which I'm sure are not easily replaced.

So, to the topic at hand, last night and tonight I worked on taking apart the steering rack from the '64. In keeping with my transmission rebuild, I've decided to include a picture of the steering rack from Canley Classics (and which is also a copy of the one from the parts manual) and will use the part numbers listed to help the discussion.

Should be able to read most of the part numbers on here, hopefully.
I had previously tried to take this thing apart a while ago but got my butt kicked by the locknut (42) and I didn't want to break anything. This time, however, I put the whole rack in the vice, put a large adjustable on the locknut and knocked it with a 4 lb. sledge. It worked, though not in the order intended.

Weapons of choice.
Doing it this way loosened up the inner tie rod (or ball pin (37)) but this was just fine with me. 

(Bottom to top) Ball Housing (36), ball pin (37), and the ball socket (38).
I put the rack in the vice again to remove the rest of the nuts. Because I kind of removed it backwards, the (lock) tab washer (39) came off before the locknut and adaptor sleeve (40) and spring (41).

(R to L) Spring (41), tab washer, adaptor sleeve, locknut and end of steering rack.
Blurry...sorry. The locknut backed off using the weapons of choice.
I did the opposite side of the rack the same way. The order came apart differently this time, but in essence the end result was the same.

Next was to take apart the pinion housing (21) to get the pinion itself out which would allow removal of the steering rack (22). The grease nipple cap (35) and screwed cap (34) came off without issue, but the cap required the weapons. I had some issues with getting the plunger (31) out but it was just because it's in there under tight tolerances and it needs to come out very straight. Painful but easy.

Next was to remove the pinion (25) itself. This proved more difficult. The rack and pinion body is made of aluminum. However, everything in it seems to be steel. Dissimilar metals sets up an opportunity for corrosion...galvanic specifically. While its chances are not great between iron and aluminum, after 50+ years...it's going to happen. So, I used a combination of an overnight soak with WD-40 and some propane heat today to break it up. I did have to use some more weapons of choice (different choice this time) but was successful while being very careful not to damage the splines on the pinion where the steering joint (15) connects.

Using a small pry bar and hammer to pop out the pinion.
The pinion, post clean-up.
The pinion comes out with a sandwich full of stuff. Of note, there is a little pin (not shown) that locks the thing rotationally. Almost lost that about four times before I finally got it in a Ziploc.

The recess for the pin is in the very top.
Also in that sandwich is a rubber o-ring that helps seal in the grease. For me, it was obvious that it was no longer in serviceable shape (squared off on the inside and stiff).

Thrust washer and its o-ring.

Trying to show the recess of the thrust washer where the o-ring sits.
Once the pinion and its sandwich was removed, the rack could be removed. Unfortunately, the rack tube had some corrosion in it because it was a real pain to get the rack itself out. Fortunately, I was able to pry it out with a screwdriver using the rack teeth until I cleared the problem area.

Flat blade screwdriver in a tooth recess, prying "up" in this picture, against the rack tube body.
Future me problem to figure out how to properly clean the inside of the rack tube to remove the corrosion. I'm sure I can use vinegar to break it up, but how to get the tube nice and clean and smooth..?

Other than that, I am soaking the rack and pinion body itself in some Purple Power to get the nasty old grease out of there. I am also soaking the rack mounting hardware (53 through 56) in vinegar to break up the rust for future cleaning and painting.

Vinegar soak. Used vinegar, hence the cloudiness.