Featured Post

Subscribe!

Tuesday, February 12, 2019

Raptor Liner on Bulkhead & Other Work | Roundtail Restoration

Moving right along with progress, but I haven't taken care of that pesky rear wing yet. As a matter of fact, I'm made it worse before (hopefully) making it better.



First up was to get the bonnet back into epoxy primer. I had originally intended to go right to build primer, but I was outside of my 7-day window and also had some exposed filler that I wanted to get covered, so back into epoxy. I also experienced some epoxy adhesion problems pulling the tape off from doing the Raptor Liner in the wheel arches. Guess I didn't clean / scuff the existing paint well enough.

Spots where the epoxy lifted off. This was taken after scuffing it back up with 180-grit.

After prepping the bonnet and taping off the wheel arches to prevent overspray, I switched over to the driver's side rear wing. This ended up not going so hot. I didn't do a great repair in the first place and it was coming back to haunt me. I tried with the stud welder to pull the lows out and it started out okay.

The deepest low area. Studs already pulled out and cut off.

Areas ground flush.

As I continued to work it, however, it became obvious that it was getting worse. My poor welding along with a lap joint were going to cause more problems than they were worth and, in the end, I cut the whole seam out.

A tear in the thin metal from my intial repair.

After beginning to cut out the bad area, shown from inside teh bonnet.

The offending area removed. Time for a patch.

By the time I came through that, it was getting late and I wanted to get the bonnet and bulkhead into epoxy before I left. I switched over to the bulkhead and scuffed it up with 180-grit sandpaper and a red scuff pad (for the hard to reach areas).

Inside of the bonnet ready to shoot. I focused only on the areas that I worked.

The bulkhead area prepped and ready.

With prep work done and the metal cleaned with wax and grease remover, I got them both back into two wet coats of epoxy.

Bonnet. You can see some low areas if you look closely.


Closeup of nose where the filler was applied.
I was happy with how it all turned out, but the bonnet needed build primer. It was obvious where I had taken it down to bare metal as opposed to just scuffing the existing paint. That would have to wait for the next visit.

Bulkhead.

I was happy with the bulkhead. There was still some evidence of pitting, but I never intended to get it totally smooth and I was happy with the end result. With the smell of epoxy in the air, I called it a night.

Next visit, my goals were to continue work on the rear wing and to get the inside of the bonnet in build primer and the bulkhead in Raptor Liner. Two out of three ain't bad.

The build primer on the bonnet was first. It didn't fill all of it, but I decided to call it good for now in the interest of concentrating on the body. I'll probably come back to it later, however. I couldn't get any pictures that really showed the post-build primer result, but the video catches some of it. That done, I got the bonnet off the stand and on its end and covered.

Until we meet again...

Then it was on to Raptor Liner. Did I mention that this stuff is just awesome? Very forgiving, very easy to apply. I also got the brackets for the pivot tubes for the bonnet that go in the wheel arches done.

Brackets.

Bulkhead. Oooooo, ahhhhh.

Then it was on to the rear wing. I didn't get very far, but I think I'll be able to make it work. When I first put it in, I realized that it had to be under a bit of tension to get it to bow out to the correct shape (I found the same thing for the rear valance). When I cut the big hunk out of it, some of that tension was released and it flattened back out.

I used my contour gage and compared the passenger's and driver's sides and was able to get a very small patch tacked in, under tension, that came pretty close to getting the angle correct. We'll see if it continues on that way, but for now, I'm optimistic. Again, the video does a better job of showing this.

Cute little patch.

That was about it. My goal for the next round of visits is to get that patch done and then move on to body work on the body itself. Still a good amount to do there, but I can see that dim light at the end of the tunnel, I think!

Friday, February 8, 2019

Raptor Liner on the Bonnet & Tail Light Repair - Roundtail Restoration

A few productive visits including fixing the tail light and getting Raptor Liner in the front wheel arches. The video:


In addition to those two things, I also wanted to get the bulkhead cleaned up and in Raptor Liner as well, but I didn't quite make that goal.

On the bonnet, I needed to get it sanded down in preparation for epoxy application. While I had done this several months ago during bonnet repairs, it wasn't ready for paint and it needed another go through. Not much to it - just hitting all of the areas with various scuffing techniques (palm sander, sand paper, red scuff pad, etc.) trying to scuff it up as best as I could. Some spots were tough to get to, like under the wheel arches, but I knew that going in. I had used a paint brush to get the more inaccessible surfaces where I knew the spray gun just wouldn't reach.

Almost ready. You can see the epoxy around the wheel arch area.

Slightly closer view.

With that done, I decided to move on to fixing the rear tail light area. If you remember, this area took a pretty good shot at some point and my initial repair, while required, did not adequately address the proper fitment of the actual tail light. In short, the area where the tail light bolts up should be very flat and instead, mine "drooped" towards the bottom. This would result in a huge gap between the metal of the car and the tail light assembly itself. Not acceptable. So, I cut a large slit in the metal and then bent that portion of the wing out so that the tail light assembly would fit flush to it, as I discussed last time.

Refresher. No, I didn't need the red plastic, but it looked cool!

Once I got that fitting properly, it was time to weld in a patch or three. I did it in little sections to make the repair easier since that area has some rather complex curves.

First patch tacked in. Still some gaps to fill around it.

Second patch fit in there.

And tacked in.

Final patch set in.

And it all welded in. Not pretty, but effective.

Same shot, different angle.

With that done, it was time to shift back to the bonnet, which I got in two wet coats of epoxy primer. Easily the most difficult time of painting I've had yet given all of the hard to reach areas. But, I was happy with my coverage when it was all said and done.

After the first coat. You may seem some red showing through, especially around the wheel arches.

A closeup in the headlight bucket. Hard area to get at, even shooting through the headlight hole because of the angle.

Another first-coat shot, the red showing through a bit more obviously.

Armed with the lessons learned from the first coat, I was able to get the second coat on with total coverage except for some areas right under the hard curve in the nose (I figured this out on the next visit).

Two wet coats!

That was it for that visit, but I got back for another quick weekday visit to get the seam sealer on there. Not much in this case; only in the wheel arches and where the wing welded to the bonnet lid.

Like with the body, I did an application with the caulking gun followed 30 minutes later (following instructions for it being paintable) by an application with the paintable seam sealer to ensure a good water-tight seal.

Application in wheel arch with the caulking gun.

And with the paintable stuff.

Wing-to-lid application with the gun.

And followed by the paint brush.

I also got some fiberglass filler on the few repair spots that I missed. All of this was in preparation for the weekend so I could get Raptor Liner on there without missing any cure times.

The Raptor Liner went on as good as it always has, applying two coats with about an hour in between coats.

Driver's side.

Passenger's side.

I also decided to get filler up in the nose. There were a bunch of dings and pits from using the stud welder up there. While I wasn't as concerned for a straight, smooth finish like I was on the other side, I didn't want it to look too awful either, so I used filler to help me out.

Filler after sanding. You can see some of the holes for the TRIUMPH letters.

Somewhere in there I also cleaned up the weld repair to the tail light area. This will require filler work but, since it was now in bare metal, I need to get it in epoxy first.

In the last few minutes of the visit, I did take a sanding block to the driver's side rear wing to see what I was in for.

Yup, as bad as I suspected. But not really any worse than the other side.

That was about it. Work continues!

Sunday, January 27, 2019

Bonnet Build Primer and Some Body Repairs | Roundtail Restoration

I put some extra hours in at work during the week and, since I'm not authorized overtime in my job (I did enough in the Navy, thank you very much) I had 40 hours early on Friday...like 10am. A few errands and I was at the garage by 1pm! I also got over there Saturday morning before a basketball game, so a full weekend day's worth of work was had. To the video:


Thankfully, the temperature was just fine for epoxy primer so I was able to get the bonnet back in epoxy following all of my filler repairs. Given that the epoxy should sit overnight (at least) before you do anything with and it looking like I was going to be able to get back over to the garage on Saturday morning, I wanted to get it painted ASAP.

Which is the best side. This...

or this?

I'm still struggling with good overlapping coverage - some dry spots, but I got full coverage between the two coats. I kept the respirator on for most of the rest of the visit due to the ambient fumes and got to work on the bulkhead.

I had filled a lot of the pits and other areas of concern with filler, both "regular" and fiberglass, and it was time to smooth it down. I cheated a bit and used the angle die grinder with my roloc fiber sanding discs to help me out so I didn't have to hand-sand it all. I'm not too concerned with the final result in this area so if there are imperfections, I'm fine with that. There's a lot of stuff going on in the bulkhead area (heater hose, wiring, master cylinders, etc.) so a lot of it will be invisible anyway. That being said, I wasn't going to leave it looking like total crap, either, so I got to work.

Initial filler removal. The area to the left of the clutch master cylinder mount is a mess (still).

After working, second round of filler applied. This was pretty much it once it was cleaned up.

That done, I moved on to the passenger's rear wing, blocking out the epoxy to show me the high and low spots. Not too bad for highs, but there were several lows, of course. 50+ years of use will do that to you.

Screen capture show the first look after blocking. Dark spots are the lows (lots of them).

Unlike most of my body work so far, except for maybe the doors, the rear wings are nearly inaccessible from the back. This makes it challenging to get a dolly in there to be able to push out on the lows while hammering off-dolly to bring down the highs.

After blocking and a bit of hammer and dolly work. Coming along nicely.

One spot that will require more thought and planning is the sill area where it mates with the rear wing. I didn't do a great job in this area initially and I wish I could have that moment back to do a bit better work there. But, I'll have to make it better now. I'm looking for suggestions on a good fix so if you have any, I'm all ears!

The seam, specifically, is what's jacked up. Yuck!

Also, after the initial assessment, I figured out that my repairs to the dent in the rear wing near the tail light weren't sufficient to ensure the tail light would sit flat. Again, I didn't take a before picture, so you'll have to suffer another screen capture.

Notice, towards the bottom, that it's not flat across the face of the tail light mounting point.

Anyway, I did as much hammer and dolly work as I thought I could and then resorted to filler. Right above the center of the wheel arch, in particular, I had to rely completely on filler because there is no access behind that spot because of the inner wheel arch itself.

Initial round of filler.

I blocked that area out and, finding spots I missed of course, did another round of filler.

Blocked out following second round of filler.

I was pretty happy with it at that point and moved on to the tail light repairs. I initially tried the stud puller, but that wasn't working. Instead, I decided to cut a relief in that area to allow me to pry out the tail light mounting plate. I still need to work on a patch, but that will be the next visit.

Close to where I think it needs to be. I didn't have a tail light assembly at the garage to test it.

Same area, different view.

That done, it was time to get the bonnet in build primer, so that's what I did. I got about 3 coats on there, good coverage all around. There were a couple of concerning areas that I didn't mention in the video and didn't take pictures of (of course!) like sanding scratches and some spots where the filler wasn't sanded to feather. Thankfully, it appears, though I haven't blocked it yet, that it filled all of those areas nicely.

It looks good...trust me.

That nose is nearly perfect. Not quite, but close. Thankfully, I'm not painting Dorothy black!

That was about it. I did sneak over there today to flip the bonnet over (with help this time) so that I can get the underside of it in epoxy. I also brought a tail light assembly over to see how that fit up. I bit more fine tuning, but otherwise it's much better that I would have been!

Pretty close. Huge gap to fill.

Slightly different angle. Same gap, though...

Cheers!