Featured Post

Subscribe!

Friday, October 23, 2015

Spitfire Body Removal Preparation #3

Not much further now. I got to those last two bolts that I had mentioned were through the rear seat pan. They were under some sound deadening material, which is why I missed them the first time. Turns out that stuff was factory, as answered by several folks on my favorite forum. Seems to me that it was a waste of time with so little, but it must have been worth it to Triumph to apply it. One response to my forum question was that it was "applied by the factory in a pathetic attempt to muffle the sound of a failing diff." It's a heavy tar-like stuff about 1/4" thick and I'm sure it's both an environmental hazard and carcinogenic. Yes, Mom, I'll be careful!

Pretty brittle stuff, so it came up easily. Hole is where the bolt goes down into the frame.
After a quick lift on the boot to make sure the body was truly liberated (body can't weigh more than 300 lbs), I continued on with stripping the body clean. Since I will have to store it in my backyard during the winter, I want to get as much stuff that will not suffer the weather well off as possible.

I pulled the window out of the hardtop (the rubber seal was dry rotted) and took that and the hard top up to the attic. Thing barely fit, but it's up there and out of the way (and the weather).

Hard top glass (foreground) and windscreen. Wrapped in mover's blankets in the attic.
 I also pulled the freshly installed instrument cluster back out (hey, it looked good while it was in there) and pulled the windscreen frame.

Instrument cluster back out.

Windscreen frame out. The car looks like a race car with nothing sticking up...all the more reason for that racing jack!
The steering column came out and up to the attic as well.

Steering column and instrument cluster ready to go to the attic. That's the original steering wheel (Herald-type).
The last thing I did was strip the wiring harness. It came out rather easily without damage except to stuff that needed repair anyway. The tail lights were a bit painful, but I eventually figured out the trick in loosening the clasp that held the bullet of the wire (sorry, no pics of that). One spot of trouble was fishing the harness through the driver's side floor crossmember. The PO had done a combination pop rivet sheet metal and fiberglass floor repair. Most of the hold in the crossmember that the wiring came through was caked with fiberglass so I had to chisel that stuff out.

Front of driver's floor crossmember where wiring comes through...pre-fiberglass destruction. Original snap is still there, though!

Looks like a bunch of spaghetti, but a very simple harness. Needs a hand-over-hand inspection/repair/re-wrap.
As with the black car, the rear license plate light housing was in bad shape and I couldn't get the bolts off. I didn't cut through it this time (not yet) but I destroyed it trying to get it off because of how much rust damage there was. Future me repair.

Finally, I pulled a lot of the miscellaneous electrical stuff (starter solenoid, control box) mounted to the engine compartment portion of the body.

The last several things to accomplish are to remove the master cylinders, get the throttle linkage, all of the rubber, put the gas tank in the attic and remove the doors. I intend to spot-weld in some square tube to support the body when the doors are removed and before I move the body to prevent any chance of the thing folding on me when it is moved (that would suck). I'm sure there are other odds and ends (like the seat rails you see in the above picture), but that should about do it. Some 2x4s to make some sawhorses and a lean-to for rudimentary weather protection and I'm all set!

Monday, October 12, 2015

Spitfire Body Removal Preparation #2

Some more work today. Got a few hours before dinner and after a nice family outing for Halloween stuff and pumpkin picking.

As far as the checklist went from the last post, I got 10 of the 12 body bolts (I missed the two that are on the ledge behind the seats), the radius arms and the steering column. My youngest helped me with some of the bolts before his soccer practice.

I started with the radius arms since I figure they would be the worst. The passenger side was first and its nyloc nut came right off but, as expected, and the bolt would spin, but not pull out, even with some manual persuasion. Since there isn't a lot of room in there to swing my 3lb sledge, I had another one of those brief moments of genius and put my trusty Harbor Freight Ball Joint Separator to work and was able to push the bolt out. Once it became flush, I was able to use another short and smaller diameter bolt and have it then push the radius arm bolt out the whole way. Pretty proud of myself on that one, especially since it popped quite a few times on its way through as it broke the rust bonds. I'm sure I would have never gotten it out so easily otherwise. The driver's side, however, came right out. Something must be up and, sure enough, the bolt seemed to be zinc coated...or at least not original and I (or, should I say, my youngest) was able to spin it right out.

Tie rod separator set up before bearing down on it the first time.
Success! A no blood loss!
Something tells me this bolt is not original...and also not the focal point of this picture..sorry.
After the radius arm removal, it was on to the bolts under the gas tank and then I worked my way forward to the 6 bolts inside the passenger compartment and the two bolts in the engine bay. All of these came out without a problem, though the one in the driver's footwell came with a lot more metal than originally designed.

The youngest doing the bolts under the gas tank.

Here he is on the passenger's side floor cross-member. Small hands, big gloves.
In there somewhere is a 1/2" bolt head. Everything extra is floor pan...oh, boy.
I then moved on to the steering column. That was a bit of a pain, but I did get it separated. You have to remove two mounting brackets for the steering column inside the passenger compartment and this can be a bit painful since there is little room for your body and less for the wrench. After I got those out, I undid the bolt on the steering knuckle closest to the steering rack first. Note that, at least for me, I had to pull the bolt all the way out. Until I did that, I wouldn't budge. Of course, it may be all of the grime on it, but there you go. That out, I pulled on the steering column and in a few tugs it separated from the steering rack. I then removed the upper bolt on the knuckle and used a small hammer to knock it off the inner steering column. The knuckle went immediately into a small bucket of Purple Power and I left the steering column detached, but not totally removed.

The passenger steering column parts needing to be removed.

Yuck!

Hanging in the breeze.
That was about all that I got to. I still need to disconnect the accelerator linkage, but I don't foresee a problem with that. Oh, and I did end up missing two bolts that are on the ledge right behind the seats, but those should come right out, too. After that, the body will be liberated for, I suspect, the first time in almost 50 years. I do intend to pull the windshield frame, the instrument cluster (too much work already done to take the chance of it getting messed up) and both doors to make the body that much lighter. I also intend to put some square steel tubing in the door jams to provide some support since the sills are obviously lacking. Hate for the thing to fold in half on me!

I put the jack under the front corners of the body to do a check to see if I got everything and it came up fine. However, the passenger's side front sill is essentially gone and for every little bit I lifted the body, it crushed in just a bit less...nothing there but rust and future tears, I'm sure.

All in all, after a bit of a dry spell filled with thoughts of despair for the amount of work to do, this weekend was productive and motivational. There is a lot of work...I accept that. I also want to do it right, which will entail more work and more time. As much as I would like to put her on the road in 2016 in celebration of her golden anniversary, I doubt that she will be on the road until sometime in 2017. But, I'm okay with that because I hope she will be solidly on the road vice "just barely" and, after all, she probably deserves it!

Sunday, October 11, 2015

Spitfire Body Removal Preparation #1

Started the preparation for body removal today. Some of the stuff was already done based on work in progress so now there are only a few things left prior to being ready to pull it. As the Workshop Manual lists it, on page 5-202:

  1. Disconnect the battery cables (Done), remove the battery (Done) and disconnect the following cables and controls:
    • Cable from oil pressure switch (Done)
    • Front end lighting cable at the snap connectors on top of the air duct (Done)
    • H.T. and L.T. cables from the coil (Done)
    • Both cables from the generator (Done)
    • Cables from the temperature transmitter (Done)
    • Earthing cable from the engine (Done)
    • Tachometer drive cable from the distributor (Done...found this broken, though it did work the last time I ran the engine. Hate to have to route that damn thing through the heater again...what a pain!)
    • Choke and accelerator controls at the carburettor (Done)
    • Hydraulic pipe at the connection between thc brake master cylinder and three-way connector adjacent to the front suspension on the left-hand side of the car (Done)
    • Handbrake cable (Previously done for repair)
    • Accelerator relay lever (1 mills pin and split pin with washers) (Not done)
  2. Remove:
    • Bonnet (four bolts) (Not done)
    • Both seats (One already done, pulled the passenger's, so done-done)
    • Four bolts securing the facia support bracket to the floor (Previously done for transmission pull)
    • Floor covering (Done, but never really there in the first place)
    • Spare wheel (Done)
    • Fuel tank (Done)
    • Release all clips securing the cable loom to the chassis. Pass the cable loom under the outer left-hand side tie rod and withdraw the loom clear of the engine (Done)
    • Release the clamp bolt from the lower steering coupling and push the inner column upwards, clear of front suspension (Not done)
  3. Disconnect the radius arms from the body (Not done...and not looking forward to it, either!)
  4. Remove 12 bolts securing the body to the floor (Not done)
  5. Attach lifting tackle and lift the body clear of the chassis (Definitely not done).
Unless I missed it, the manual does not mention removal of the hydraulic pipe between the clutch master cylinder and the slave cylinder, so I did do that as well.

Not too bad for about 2 hours of work. If figure if I can get some solid time tomorrow, I should be able to get everything else done with the exception of the bonnet removal (I don't plan on doing that until just before I pull the body). I should be able to get the accelerator relay lever and the steering column done without much issue. That shouldn't take long and I'll give it a shot at the radius arms and see how they go. Hopefully I'll get lucky there and they will unbolt easily. Otherwise, I'll soak them in some WD-40 for a day or so and revisit.

The "three-way connector adjacent to the front suspension on the left-hand side of the car"
Master cylinders drained. I put a paper towel in each reservoir and in the pipe holes.
The wiring harness in the engine compartment was in pretty sad shape. I think I may have mentioned that, with the exception that the dynamo is not charging the battery, I have not found any electrical faults in the car. However, the wires up there have insulation that is cracking and some have been repaired (poorly) with new connectors at least once. And years of oil leaks and general road grime has left several of them covered with that black gooey stuff common to LBCs. I figure a visit to British Wiring (or some other source that may be cheaper) will solve all of my problems. A full wiring harness refresh will be in order once I get the whole thing out of the car, especially since I have the black car's harness as well.
The hole through which the engine compartment portion of the wiring harness comes through. Need a new rubber grommet.
The harness. Hard to tell, but there's grease and grime all over it. Pretty sure they used all blue harness wrap, too. Nice.


Finally, my latest Harbor Freight purchase was their 1.5 Ton Compact Aluminum Racing Floor Jack with Rapid Pump <whew, that's a mouthful>. There was a coupon for about $70, so I picked on up. I have a big, heavy Craftsman 3 ton jack that I purchased over a decade ago. It's built like a beast and of good quality (think before Craftsman went more the way of Harbor Freight with some of their stuff) but it was too big for jacking several points on the car. I like to use a wood buffer between the jacking point and the jack itself. Unfortunately, since the Sears jack stood so tall, I either couldn't fit the wood in between the car and the jack or, if I could, I couldn't lift the handle enough to actually start the jack going up. Since the HF one is low profile (and racing, did I mention that...so I can pretend I'm doing pit stops on her, obviously), both of those problems are solved. Haven't used it too much yet, but it jacks the car up without any leakage, so it's go that going for it.

Saturday, October 10, 2015

It's About to Get Real

After some soul searching and sage advice from a co-worker who has been down the road of VIN assignments and the Connecticut DMV, I've decided to take a bigger plunge and pull the tub on the car. As I mentioned in my last post, I found the spot of cancer in the frame and that outrigger is shot. My co-worker said that they wouldn't fly with the DMV and suggested that, along with the holes in the floor and front corners, I would be wise to do the repairs instead. This guy shares the same love for cars that I do, more probably, and has much more experience in them than I do. He also offered to help, so it was a no-brainer.

The plan is to pull the tub and put it on sawhorses in the backyard next to the black one while I clean up and repair the frame.  Of course, the tub is going back there at the start of cold weather and will endure the harshness of winter, so I intend to build a lean-to into the sawhorses to try and protect it as much as possible. Then, with a solid core, rebuilt suspension and other bits, I can swap the frame for the tub and work on that. Oh, and I'm sure along the way the engine will come off so I'll probably take care of that to, to some level, at least converting the head to run unleaded gas (valves, guides and seats).

In a way, it's a bit of a relief because at least now I know my way ahead a bit more and I've removed the anxiety of trying to get the thing to pass inspection "just barely". Since I really don't have any intention of selling the car and since it is just a hobby (though a passionate one), it can wait to be done correctly.

Today, towards that end, I did some more cleaning of the garage and moved a significant amount of parts to the attic. I pulled the gas tank that I had just put in (though had not piped or filled) and otherwise made small inroads into pulling the tub. Since this will be the second time for me, I hope it will go a bit smoother, though I will be taking much more time in labeling and documenting everything much better since I'll want this one to go back together someday. Unless some suspension mounting parts become painful (like the radius arm problems I had with the black one), I suspect I should be ready to pull the tub by the end of next week. Out of town next weekend, though, so hopefully the weekend after that it will be ready to pull. Then, the fun will begin.

As for actual work, I decided to tear apart the windshield washer motor and remove that 50-year old grease as well as clean it up and refurbish it a bit. The wire that runs from the internal brush to the windings was in bad shape so that will be replaced.

Mostly pulled apart. You can see the insulation cracked on that wire. It did work when I pulled it out.

The usual suspects.
That was about it, really, for the car today. This morning, however, I had the pleasure of taking the family to see the christening of the USS Illinois (SSN 786) at General Dynamics - Electric Boat here in Groton, CT. As a career Navy man myself, this was one of the only major Naval ceremonies that I had not witnessed. The Navy and the shipyard approved cameras, which was a surprise. I didn't think far enough ahead and failed to charge my point-and-shoot, so the pics were with my cell phone.

As a native of Chicago, Illinois, Michelle Obama was asked to be the ship's sponsor and she laid the keel about 16 months ago. The weather was beautiful, the speakers were actually pretty good (though I don't think my boys agreed) and it was another impressive show of our nation's military men and women. I had actually contributed a very small part to the ship's construction, testing some of the nuclear plant before I switched jobs, internally, to now teach nuclear theory, so it was nice to see it all come together. She has a few months before she is ready for sea trials.

Obviously we weren't that close, but the official party and crew are on the ship.
Michelle Obama, the ship's sponsor. Again, not a great picture.
This is the USS Colorado, under construction, looking aft. Inside that little tan building sits the reactor plant.
Since this was the USS Illinois, the theme was Chicago and there was a live Blues Brothers-style band (funny...the lead singer said they usually didn't start playing much before 10 PM let alone before 10 AM), Chicago-based food (loved me some Chicago hot dogs) and everyone got a pair of Blues Brothers sunglasses. Don't worry, those were not your tax dollars at work as the shipyard pays for all of that stuff. Of course, your tax dollars pay the shipyard, so...

Saturday, September 26, 2015

Not a Good Day

I've been in a funk most of the day. It started out good, with exciting plans, as some weekend days do. But, it went downhill rather quickly.

Today was the day for the British Wheels on the Green car show. This show is hosted by the Jaguar Club of Southern New England. If you remember the blog post from last year, it was the first British car show that I had been to and fueled my restoration fire about a month after purchasing my Spitfire.

Today, I got there early (around 10:15am) after dropping the oldest off at basketball camp. Not long after I arrived, the wife called to inform me that the family truckster would not start. Mind you, this is the Honda Odyssey that has graced these pages a few times before (headlights and rear disc brakes). Last week, I had a local shop replace the serpentine belt, the alternator (shot bearings) and battery. That was about $500. Not horrible, but I didn't want to, nor was I confident, in doing the job myself. This car is just over 100K and we are fighting over buying a newer car, or putting a couple of grand into this one for milestone maintenance (timing belt, water pump, etc) and trying for another 100K. Regardless, after the work done, I would expect the car to start especially since it not starting was the reason for bringing it in in the first place.

Since I was early to the show (it started at 10am), I made a bee-line for Ikea about 25 minutes away to get a new desk chair and was back to the show by noon. The car population hadn't really improved all that much and I was disappointed (again, too high expectations).

The car show was ok, but not as good as last year. While there were still several fine examples of Jags (being a Jag show and all) the "other" British cars were not as well represented. Two squaretail Spitfires and a GT6 and two TR6s were the only Triumphs that I saw. Oh, and a Herald, which was nice to see since I hadn't seen one in person before...left hand drive, even. Otherwise, some nice MGAs, a really nice Jag XK150 and the "usual" smattering of E-Types.

The dash of the nice MGA. Lots of orange peel...but who am I to judge?!
XK150. Picture doesn't do it justice.

Nice looking car!
That was about it for the show. I walked around and took some pictures and had a slice of pizza and a Coke from a local vendor but left by about 12:30 to voyage back home to do some work on the car before a dinner party at a friends house.

By the time I got back from the car show, a neighbor had charged the truckster's battery (it was at "75%" according to whatever charger he used) and the car was starting fine. Some basic troubleshooting told me that I have a good ground and no stray amps going where they shouldn't...???

For the Spitfire, my goal for today was to swap out the fuel tank and route a new fuel line borrowed from the '64. The new tank went in fine and lined up nicely with the fuel filler cap (unlike the "old" one). While I was under the car trying to route the fuel line that ended up being too short, I decided to dig around with a flathead screwdriver a bit. Probably should have done this before I bought the car, I guess, but I'm all in, now. The passenger's outrigger I knew was shot. The driver's, however, I did not know was also shot as bad as it was. The driver's sill is also in bad shape and I will assume the passenger's as well, though I didn't poke around. Of course, I should have expected this given the cancer that is obvious from the inside of the car...but today it was in my face and made me afraid that I wasn't up to the task...both financially and skill-level.


Remnants of digging around in driver's outrigger.

Digging done, though not complete. The bottom pipe is the too-short fuel line. Pic doesn't show cancer in the frame.

Bondo heaven. Those white marks in the upper center are Bondo as well. There was a pile of on the floor after this, too.
While all of this was a blow, I'll be damned if I'm defeated. After 23+ years of naval service, I am happy to be able to re-kindle the excitement of my youth in fixing up old cars. The more British, the better. This car is a fine example of automotive engineering that has all but disappeared from the landscape. My trips to large, British car shows only convinces me that the older Spitfire examples are growing more rare all the time. Even if I have to "store" the car for a few more years, I'll do it.

Still, a rough day. Like all of the other surprises, however, I'll come through this as well. Just may take a bit more creative thinking and creative storage solutions.

Saturday, September 19, 2015

The British Invasion Car Show

A whirlwind weekend so far for us. I got out of work early on Friday and pulled the kids out of school to head up to Stowe, VT for the 25th Annual British Invasion car show. We got into town around 5:30, checked into the hotel and headed downtown to eat and look at the cars that were on display during the Stowe Main Street Party. Some nice cars but I unfortunately forgot my camera and I was sure I would see them the next day.

After a fitful night of sharing a bed with my oldest, we were up and at the event field by about 9:30pm, about 30 minutes after the show started. LOTS of cars there. I would say that the Austin-Healeys and TR6s were the cars in most abundance. However, there was just about everything you could think of.

We walked around for the better part of three hours. Unfortunately, there were only 3 roundtail Spitfires there, all Mk3s. They were fine examples, however. The rest were squaretails, with one being a survivor with the original paint and striping...pretty nice.

All in all, I am sorry to say that I was disappointed with the show. I will temper that, however, with my obviously unreasonable expectations of a good amount of Spitfires, especially any older ones, and several parts vendors, with a bunch of NOS parts. Like I said, there were maybe only a dozen Spitfires, all but 3 of which were MkIVs or 1500s. And the only vendor there selling some NOS stuff was a guy that I remembered from the British by the Sea show and he really didn't have anything that I was looking for.
I will say, with the fact that Spitfires seem to go for "dime-a-dozen" prices, they sure are under-represented at the shows. This is the third car show I've been to now, with two being what I would consider sizeable (the British Invasion, according to one announcement I heard, is the largest British-only show in the U.S.) and outside of the very rare cars, I'd say that the Spitfires were the fewest and far-between. Now, there could be a few reasons for this; people don't want to spend the money on these cars because they aren't worth the time and effort to get them into a show condition; people just don't consider them show-worthy in general; there just aren't too many good examples of these cars left and we are going to wake up one day and realize it!

All that being said, there were some VERY nice cars there, especially in the Concours d'Elegance. There were also several cars there that I had never seen in person and a few that I hadn't know existed in the world. I did get a few old magazine/newspaper ad reprints, a Triumph ballcap and T-shirt and my wife found a few blankets that are made from something called Bronte by Moon wool. I guess this is pretty nice stuff...my bank account thinks so, anyway.
So, while I was disappointed for my own selfish reasons, I was able to share my LBSC passion with my wife and kids on a much grander scale while also enjoying the beautiful town of Stowe, VT that hosted it.
And, if nothing else, it motivated me to continue work on the car to be able to represent the older Spitfires as future shows!

Now, for some pics.


One of the TR3s (of two) in the concourse judging. Afraid to touch it!
The interior of the above TR3. Hazy through the rear soft top window.
A Daimler? This was a new one to me...gorgeous car, though.

Unrestored, original paint and interior, 16,000 mile Austin Healey. Wow.
The boot, with spare, of the above car. Can you read the tag on the spare tire?
Another survivor...MGA twin cam. Original and only owner, never restored.

Jag D-Type.

Beautiful E-Type. Love the paint color.
Gremlin found!!

Very clean Mk3. 
A trip to VT would not be complete without a covered bridge.

According to Wikipedia, it is listed in the Register of National Historic Places. I think the family got nervous when the GPS called out "Turn left on Slaughter House road and you will arrive at your destination".






Saturday, September 12, 2015

iPhone 4 and Drywall Repair (umm, yeah, a bit off topic)

A couple of unrelated things from the last few days for those that may want to mix it up a bit.

First, we decided to get my oldest, who started 7th grade this year, his own phone. Since I always keep my most recently upgraded phone just in case, he was going to get that hand-me-down iPhone 4. After two years of use as my primary phone and then another two years as his iPod, it was showing a little wear and tear. Namely, the home button didn't like to work unless you mashed the heck out of it. After some research and a visit to iFixIt.com, I purchased a new home button and the tools they recommended to replace it. Of note, this was a Verizon CDMA phone vice an AT&T GSM phone. I guess they are different besides just the SIM card in case you take on this type of adventure.

While the website says the repair is difficult, I didn't have too much problem. The instructions were not perfect, but they were definitely good enough to get me through and the pictures helped. Unfortunately, I pinched and tore one of the ribbon cables for the display so a $10 job (not included tools) turned into a $40 job, which I was able to complete successfully. I know the phones are generations old now, but I was surprised at how cheap the parts were. Makes me wonder how much Apple is really making off of each of us, though that explains why they have enough cash reserves to fill 93 (yes, 93) Olympic swimming pools.

I did have to wear my glasses and needed some extra light. Don't think I've ever dealt with screws that small before, but the magnetic tools made them easy to handle.

About half-way torn apart. Plastic tray was essential in helping me organize each step of the tear down. 

Almost completely torn apart. New home button in (display not damaged yet).
I finished fixing it last night and the boy was happy to get it back.

Second, I needed to do some drywall repair in the bathroom that I am STILL redoing. We finally got all the ordered items (long, frustrating story) after some backorders and bad manufacturing, so it was time to finally mount the wall light and repair the holes the original home builders left when putting in the "contractor's special" wall light. First thing was to cut some new drywall (I bought a 2'x2' patch piece at Lowe's when we first moved in and have been slowly using it) for the patches. I cut these about 1/2" larger on all sides than the size of the holes. I scored a 1/2" on each side and then broke the drywall away, leaving the paper to act as ears to cover the edges.

The small piece, cut to size and scored, leaving "white" paper side.
I then traced the drywall of my patch pieces on the wall and then cut them square, trimming as necessary so the patch pieces would fit totally inside the cutouts.

Patch-panels cut.
After that, I put a thin layer of joint compound on the paper so that it would act as an adhesive to the wall.

Joint compound. I used even less than this and still some squeezed out as I flattened it to the wall.

Patches inserted into wall.
Once the patches were in, I taped the edges with regular paper joint tape (none of that mesh stuff) and covered it all in more joint compound.

Patches in and covered.
I came back about 7 hours later and sanded it down and that's when it all fell apart. The joint compound paper immediately started to delaminate from the wall and the bumps and ridges were horrible. I probably should have waited it for it to dry more, but once the damage started, it went quick. So, in a fit of frustration (I've been dealing with this bathroom for over six weeks and I'M WAY DONE), I tore the joint paper off and the patch paper. The patches stayed in the wall, however. Once I did that, I filled the incontinuities with regular spackle and that's where it sits. I'll sand it tomorrow morning, put another layer of spackle, and sand it one more time. Paint and then finally mount the medicine cabinet hopefully late tomorrow night. At least these holes will mostly be obscured or even covered by the cabinet so you won't see my horrible job!

Same holes, except with just spackle. Looks better and much more level. Spackle won't be as durable, but up there, I don't care.
We also got the second backsplash in since the first one was not completely sealed (it's granite). That went in easily and really completes the sink in it's look.

Backsplash in. I used clear-drying caulk adhesive to put it in. The medicine cabinet will go in the big blank spot.
As for the Spitfire, I did some more odds and ends today after the drywall fiasco and before the kid's soccer games. I finished putting the rubber grommets over the inside portion of the speedometer and tachometer cables (has anyone ever put one of these things in without tearing the crap out of it?!), reconnected the heat air hoses that go to the top of the dashboard and put the instrument cluster in, wires and all (except the ignition switch). After the ignition switch gets wired up, I only have to put some water in the radiator and she'll be ready to run again...at least in theory!

Refurbished dash. A shame the rest of the interior looks like...well, you know. Oh, and those screws are temporary. Black or chrome?