Everything but the front bulkhead (vertical and shelf areas) is covered in two coats of epoxy. Too many dings and bumps to count, but she's looking oh-so-much-better.
As the caption says, the video is just over 33 minutes, capturing three garage visits. Given that, this post will be rather long as well.
First thing I did when I got there was give myself a motivational shot in the arm by putting my new bonnet emblem and TRIUMPH letters on, just to see how they'd look.
So nice. Except that it's not red!
After staring longingly at that for a few moments, it was time to get to work. The first visit, being a school night, was planned to involve stripping the boot area and getting it in epoxy. The leftover epoxy I had from painting the driver's side a few days before seemed to still be sprayable, so I got at prep work by stripping down to bare metal using a variety of tools including stripping disks, wire wheels, roloc sanding discs, etc.
The corners of the boot lid channel were some of the more challenging areas.
All stripped.
Once it was all stripped, I taped off the inside of the boot area and cleaned the heck out of the newly stripped area with wax and grease remover and let that dry.
Masked off, ready for paint.
In between, I also got fiberglass filler on the areas that needed it, namely my weld repairs and the multitude of plug welds.
Trailing edge of the rear wing that I replaced.
Covering the plug welds, among other things.
That all done, it was time to spray. Turns out the epoxy was a bit more cured than I thought and the initial spray did not go well, so I stopped. I didn't take any pictures, but it's here in the video.
All in all it wasn't a bad visit, but I was on a timeline for things that I wanted to get done. I let that cloud my judgement a bit, resulting in a stripping job that could have been a bit better (I fixed this on the next visit) and a fiberglass filler application that was not up to my standards. I haven't addressed that yet, but I will and probably end up with lots of re-work in that area. Shame on me. Thankfully I was smart enough to stop when the painting went screwy.
The next visit was a weekend, so I had a lot more time. My intentions this time were to strip the boot lid a bit better in the areas that I skimped on as well as strip the entire passenger's side, similar to what I had done on the driver's side. I also wanted to use the stud puller to work on the rear wing dent, then get the whole thing in epoxy. While I didn't quite get there, this visit did go much better.
I started with work on the rear wing dent. There was a pretty good crease in here that needed to come out as well as holes that the previous owner had left when he used a slide hammer to pull some of the dent out. As for the stud puller, I was happy with its performance, but the pins that came with it were crap. I invested in 500 new ones, by Motor Guard, via Amazon and these were of much higher quality and cheaper than Harbor Freight, per piece, to boot! They normally are $19.95, but sometimes the prices on Amazon mysteriously fluctuate, and I snagged them for just over $17.
Much better.
Not wanting to waste all of the HF ones, I used a mix of both to start work. I used lots and lots of pins (maybe 50) to do what seems like little work, but they were very effective in small doses, so to speak, and I was very happy with the final result.
Before any significant work. You can see the hard crease right under the tail light area.
Same time, different angle, trying to show the crease better.
Lots of pins now, working out from front to back.
A bit better. I applied heat to try to soften up the metal a bit, hence the heat bloom.
Again, same time, different angle. Crease still very much there, but better.
And better still.
Still going.
By this time, a few of the holes from the previous owner's work had "joined" due to all the pulling. Given that, I decided to stop using the stud puller at that point and just replace the damaged metal with a small (about 1" x 2") patch. This worked pretty well.
Just before cutting out the damaged metal for a patch.
Post-patch.
Same time, showing the vast majority of the crease all gone. Ready for filler, even?
Finally, I filled the little gaps and holes that I left when putting in the new rear valance.
There were holes under the tail light that are now gone...trust me. You can see some sloppy welding as evidence.
Again, I was very happy with the mostly-final results to the point where I'd even say I got lucky. This was really the last major damage, dent-wise, that I had to worry about. There are many that still aren't done yet, of course, like the nose, but I don't have any worry that I'll get them sorted - just a matter of investing the time to do it right.
With that area as done as I wanted it to be for now, I moved on to stripping the side of the car. It went exactly the same as the driver's side and I didn't find any surprises, though there were many dings, of course. It took a while, of course.
Sometime in there my plans for the weekday garage visit changed and I was going to come back the very next night. So, instead of painting, I kept going with stripping, deciding to get the front sail plate and that area stripped down. By the end of the visit, I had it mostly stripped except the painful tight areas.
Front sail plate mostly stripped.
Random brazing plug. Wonder what happened? Spot weld mistake?
The final visit of the three was another school night and I had to pick up on of my kids from basketball practice, so I had a time limit. However, there was minimal stripping of the front sail plate left and then just a bunch of W&G remover cleaning and paint mixing and it was ready to shoot.
Ready except for the fact that I forgot to fix the one soft top snap hole that was damaged.
Top blown-out hole filled...
...and ground down. Didn't even have to re-drill it!
There was also a random divot in the area around the radio antenna hole. I don't remember causing this, but I filled it with weld metal anyway.
Filled...
...and ground down. Went a bit low, so it'll need a bit of filler (that's the dark ring around it).
That all done, I masked off some of the areas and cleaned everything several times with W&G remover until the paper towels came out clean. As for masking it off, I had someone ask me why. I can't tell you why, really. The only thing I can say is that I didn't want a lot of over-spray because it just seems like the right thing to do. Maybe a waste, but it gave me some practice at masking techniques, so there's that.
Masked and ready.
With that, coat #1. Got good coverage everywhere.
Front quarter.
Front sail plate. Happy with how this came out since there were several tight spots.
Boot area.
With the first coat on, I had a 30-minute wait, so I started to work on the bonnet a bit. I did some stud puller work on the passenger's side headlight bucket and caused a bit more damage, but I think it'll work out in the end. It took a pretty good shot up there that the PO tried to repair, but ended up covering with mostly filler. I made a rounded corner into a sharp edge that was weak and I caused it to crack with my work. But, in the end, I think it will work out just fine. The video explains it a bit better than my pictures do starting about here.
A pin in.
After that work, I got back and laid down a second coat, a bit heavier than the first as I've been doing. Went down well and I'm happy with the end result.
Front side.
Rear wing.
Boot area.
Again, not a bad round of visits. Next visit, which will be a weekend, will be to strip and get epoxy on the front bulkhead. I fully expect this to take most of the 7+ hour time as there are lots of tight spots to get stripped and painted. I also have to possibly teach myself a new painting technique by using a pencil stream to get into those tight areas that a normal "fan" pattern won't reach. I'll be practice before actually laying paint down that way, that's for sure. Any work beyond that will be gravy as that will probably be my last visit of the year being the holidays and all. Until next time, cheers!
Believe it or not, I'm still caught up with my posts. I'm even putting this one up before I go back over to the garage. Amazing! And, I remembered to take lots of pictures and even tried to use some lighting to show the dents better. Turning into a real professional operation around here. To the video:
So like the title says, I got the driver's side of the body in epoxy primer. I definitely didn't plan on going that way when I showed up, but the body work just wasn't calling to me too much. That and the fact that I would like to get the majority of the dust creating stuff done (like throwing paint of the body with the stripping wheel), I decided to start stripping the body down in sections. I'm doing it in sections so that I don't leave too much stripped to bare metal at once and it also allows me to better manage my 7-day epoxy window.
I did get a good look at the bonnet now that it was in epoxy and dry. Definitely some work to do, but nothing too major outside of the nose. My concern is not the work, but the size of the workspace. I'm afraid I'll run into the problems that I did with the boot lid being such a large sheet of metal. Hopefully the center accent (the raised part running down the center) will provide some strength.
One of the dings. I can get to the back of that.
Another spot of concern. Need to look at this closer; oddly shaped dent (?)
The dreaded nose.
The worst single area to work on (besides the nose, of course).
After the bonnet once over, I looked over the body to see what awaited me and to re-familiarize myself with the things that I never fixed the first time around. I also wanted to make sure the rust that was showing up was just surface stuff. It was.
My yucky lower wing replacement on the driver's side.
The passenger's side rear wing that got smacked at some point.
There wasn't a horrible amount of things to worry about, but I'm sure it'll take time as I work my way through everything. After that, I essentially flipped a coin and decided to strip the driver's side. No real surprises, which was good, and only minor dents that were obvious. There are probably lots of low and high spots that I haven't seen yet, but I'll get there I'm sure.
Starting the stripping process.
Rear wing area done. Making my way forward.
As you can imagine, this was tedious, but pretty brainless, work, much like the bonnet. Since I was in my "paint booth", the dust didn't get too out of control. I should have done all of my stripping in there the first time around.
Work down the sill.
There are a whole bunch of plug welds that I did (most, I must admit) along the sill that have little pits in them. I'll go through on the next visit and get all of these areas filled with fiberglass filler to seal them up. There some argument out there on whether the fiberglass filler is waterproof. I was under the assumption it was, but I'm not too sure now. In any case, I have the epoxy down first, which will hopefully protect from water intrusion / rust, at least for a while.
The area around the A-post was the hardest to clean up because of all of the interference and depressions and such.
The hardest area on the side.
I got most of it by the end, but for a little bit behind the bonnet slide and up above the bonnet locating bracket. I was able to at least get a wire brush in those spots to rough up the area for epoxy adhesion.
Area behind the bonnet slide (the vertical piece of metal that bows out).
Area above the bonnet locating bracket (horizontal piece with hole in it that takes the bonnet cone).
With the cleaning done as good as I could get it, I hit everything with the DA sander to get a 60-grit swirl in there and hand sanded all the areas the DA was too big for. After that, I cleaned the heck out of everything using Wax and Grease Remover and several shop towels. I didn't use compressed air to blow anything because I didn't want to put too much dust in the air. I mixed up the paint and gave that 30 minutes to induce as well as the W&G remover time to fully dry.
Masked off. I hit it with W&G after masking it to get any last fingerprints off of it.
While waiting, I put some fiberglass filler on the bonnet in my repair patch areas. Again, I intend to cover all of my weld seams with the fiberglass filler to provide some added strength as well as waterproofing (if it really does that). I didn't spend a whole lot of time here, but did get it applied and very roughly sanded down.
Passenger's side front wing, after application and rough sanding.
Same side but the rear of the wing. Again, roughly sanded.
With the 30 minute induction time up, it was time to paint. You know the drill - two wet coats, waiting 30 minutes in between each.
Rear wing.
A-post.
Side view.
I didn't look at the overall results very closely as spraying this much paint, it gets pretty bad in the garage, fumes-wise, and I like to leave shortly after that. So, I'll take a hard look next visit and see how it came out, but I think it should be good.
I mixed too much paint and left several ounces in the mixing cup. The stuff is expensive, so if it's still sprayable on my next visit, I think I'll continue my way around the car and try to get the boot area done. There should be enough paint for two wet coats on that. If not, then we'll see what I feel like tackling. Until next time...Cheers!
You know what this means...it means that I'm caught up on my posts!! I know, right? To the video:
I decided after doing some work with my new stud welder that I wanted to get the bonnet, or at least the "outside" of it, in epoxy primer just to minimize any rusting that may occur. I also wanted to see what it would be like to spray such a large panel. It was different, I can tell you that. Much more challenging.
I flipped the bonnet over to get a look at the inside to see how much attention it needed. While it was inverted, I also got a hole filled in with weld metal that resulted when I had replaced the bonnet cone support stuff a while ago.
The hole. It filled just fine.
With that welding done, I looked over the inside. Originally I thought I would take it all down to bare metal, but thought better of it. Instead, I focused on finding delaminating paint and other rust spots and got them cleaned up. I had done this already a few times while doing the bonnet repairs, but I did a concentrated hand-over-hand this time. I was happy to find little bubbling paint and no rust that didn't come off easily with the paint stripping disk.
Showing spots that I cleaned up. Some cleanup remains up in the nose.
With that, I flipped the bonnet over to get going on the outside of it. First thing I did was fill, with weld metal, the slide hammer holes left by the PO that were previously covered with filler.
The holes, previously covered with filler.
With those done, it was time to remove all of the paint in keeping with my desire to take everywhere I was going to spray color down to bare metal prior to epoxy. What a dirty, loud and lengthy process!
Passenger's wing done.
The residue of just that bit. I frequently swept and vacuumed.
And driver's wing.
And everything else - from the back.
And from the front.
I ran out of time for that visit, but the bonnet was stripped. It was a Sunday, so believe it or not that work took me about 8 hours to accomplish.
For the next visit, my goal was to get some metal work done as I could while still leaving enough time to get two coats of epoxy on there and pick a kid up from basketball practice.
I didn't take any pictures of the metal work because, like I said before, I suck at taking dent pictures, so you'll have to trust me. I gave it an attempt in the video, but the results were "meh". I got some stuff out, but none of it would I consider ready for filler.
But, as time drew down, I moved the bonnet into the "paint booth", got it cleaned up, and shot the first coat of epoxy, waited 30 minutes, then got the second coat.
From the back.
Front nose.
Like I mentioned, it's a much more challenging time with the larger panel. Looks like I fixed by cratering problem this time and I got the epoxy where it needed to go, but there was some spots of dry spray (probably why I didn't have any cratering). Since I'll be putting at least one more full round of epoxy on it I'm not too worried, but we'll see. Unlike the doors and other stuff so far, I only intend to shoot the areas that really need the epoxy following metal work instead of the entire thing. It'll save some paint, time and just a wasted effort on something that doesn't really need it, I think.
Oh, and while I was waiting between epoxy coats, I blocked out and signed off on the driver's door. Some re-work there due to my own fault, but it came out fine in end.
Next visit will be more body work on the bonnet. We'll see just how far I can get and whether or not I can get the metal work done and start in a filler. I doubt it, but here's to hoping!
I knew that I would probably have to break down eventually and get one of these and I was correct. Getting a hammer into the nose of the bonnet was nearly impossible and using a slapping spoon and dolly wasn't really effective. A stud welder was just the thing.
Of course, I relied on my trusty Harbor Freight to take care of me and I picked one up. Like I mention in the video, I think this is one of those tools where one company in China makes them for several different retailers and they all just get different labels and, of course, different prices. Unfortunately, you cannot use coupons with HF welders, so it was full price (~$98).
The video is a bit repetitive as I try to show you how it works from different angles (I struggle with showing dents in videos or stills). But, the basic idea is that this stud welder tack-welds on 2mm or 3mm (I used 2mm based on Dorothy's sheet metal thickness) studs. Then, using a slide hammer that grabs on to the stud, you pull the dent out. That's about it, really. Unlike the slide hammers that I used as a kid, and that the PO used on Dorothy, you don't drill holes into the sheet metal and use a sheet metal screw to attach to the slide hammer and yank. That means there are no holes to fill!
After getting the newly repaired driver's door into more build primer, it was time to have some fun.
I didn't get to blocking it out, but it should be good!
My first five studs welded in.
The trick is to use enough studs, placed in the correct spot, to pull the dent(s) out. With the bonnet nose being such a mess, I used lots of studs and won't be shy about using more.
More studs.
This is an iterative process, placing a few studs and pulling the dent out, then clipping them off and maybe putting another few studs down. I did have trouble on the rolled edge of the nose pulling the dent out. Two reasons for this, I think. First, the metal will be pretty hard (less ductile) here since it's been work hardened bending it over and, therefore, difficult to pull out. I'm thinking about using a punch to try and knock it out from behind, but maybe I'll just stick with filler...or a combination. We'll see.
Attached to a dent right on the nose bend.
After knocking it a few times...nothing. Filler?
The other issue I had was a general one. The pins are relatively soft. This is great when it comes to cutting them off and grinding them down, but the drawback is that you only get a few good pulls with the slide hammer before the knurled knob has stripped away the pin and it no longer holds on the pins. I changed my method a bit to compensate for this, but in the end, it is what it is. Again, the pins are soft on purpose, so it's a trade off. Also, I think the design of the slide hammer in how it attaches to the pin could be better (hard material, more clamping force...something), but it'll do.
All in all, however, I was very happy with how it came out. There's still work to do, of course, but it is way better than it was when I started. Again, since I struggle with dent pictures, it's hard to get an appreciation for the difference, but it's very noticable in person.
Before I started working on it at all (bonnet standing on end here).
After several pins.
A bit less zoom.
Head on shot.
Again, there's still work to do here, but I'm hoping that I can use the slapping spoon and dolly to continue to flatten it all out, along with the shrinking disk. I think I can get about an 80-90% solution with that and filler will take me the rest of the way.
As I type this, I've stripped the outside of the bonnet to bare metal. I'm going to do some coarse metal work on the next visit and then get it in epoxy. Until next time...
Behind again, but a relatively short post. Also, this is another one where the video will be better than the write-up in documenting "how" and giving good pictures. With that, to the video:
Having come through the repairs to my dropped door and getting it back in epoxy, it was time to repeat the process of filler and epoxy and so one, all the way up to build primer. I won't bore you with that process (again), but I got there. I also called the front valance "done" with the exception of final prep.
Second round of filler on a spot I missed.
With those done, it was time to move on to something else. I had originally intended to start on the bonnet but, while cleaning up the paint "booth", lo and behold I rediscovered the windscreen frame. Forgot all about that!
With that, I shifted my focus and began with getting the top cap off to check for any corrosion. I had several rivets to drill out, but that was quick and easy and, outside of some minor resistance provided by the mastic tape that was used to prevent water intrusion (and some adhesion, too), off it came. It's all scratched up as you would suspect, especially since it's made out of aluminium (make sure you "read it" right...the Brits pronounce it differently).
Corner of the windscreen cap. Notice the mastic tape for a sealant.
The other thing that needed to come off was the vinyl trim around the inside of the frame. I had worked on this a very little bit when I first got the car, but now it had to come off for epoxy application.
I used a heat gun on low heat and a metal putty knife (would have prefered a plastic one, but didn't have one handy) and slowly got all of it off, in the same four (and no more!) pieces that were put on in the factory.
An interesting note here - the windscreen for the early (Mk1 and Mk2) Spitfires were borrowed from the TR4 (with the Mk3s, the windscreen frame was integral to the body). The TR4 used a different soft top attachment method, typical of what most people are used to, being two clips up on the windscreen and the soft top folding back on a frame behind the rear seats. In the early Spitfires, the soft top and frame were completely removed and stored in the boot. However, sharing the same windscreen, my frame has the bolts and holes for the TR4-style clips. Cool.
Circle where the holes are. You'll have to trust me. The other holes are for the rear view mirror and optional sun visors.
A better example on a Mk3 of the actual latch. There is no soft top here, only the header frame.
With the vinyl successfully removed, it was time to clean the frame up and get it inspected. Surprisingly, there was no corrosion to speak of. Not even minor pitting. Sometimes the water will seep between the frame and the body and just rot it all away, but I guess I, and Dorothy, were lucky in this respect.
With it all cleaned up, all that was left was to get it in two wet coats of epoxy.
Front
Back - with another look at the holes.
I took a look at some bonnet concerns at the very end of the visit, but for work, that was about it. As far as the vinyl goes, I should be able to save it. The heat gun made it very malleable, so I'm hoping I'll be able to reuse it, but we'll see. Cheers!